New fancy-pants camera. Check.
New fancy-pants lens. Check.
New fancy-pants collapsible photography lightbox. NEVAH! OK, maybe not never ever, but certainly not right now. Especially since I can whiz-bang that thing together in just over an hour.
For those of you following the Shoot I Do series, the next one is coming, but I thought I’d throw this fun and inexpensive tutorial out here first.
Are you ready to build your very own lightbox for under $20?
THINGS YOU’LL NEED:
5 pieced of stiff white poster board-sized foam board (Hobby Lobby)
1 package of Velcro (Hobby Lobby)
3 pieces of pearlized (no pattern) white vellum paper (Hobby Lobby)
Hmmm, for a gal who gets itchy inside of Hobby Lobby, I sure did spend a lot of time there.
To the lightbox!
This is the foam board. As you can see it’s thick. What you can’t see is that it is also sturdy.
Velcro! The Velcro package came with two ribbons of material. One fabric-like, one Velcro-y like. This is the Velcro-y one. It had a sticky tape backing, so I simply cut to size and took off the protective backing, then stuck it to the bottom of three boards.
As you will see in a minute, the boards will be “standing” and this is the bottom portion with one side of the Velcro stuck in place. Please take note of my imperfect cuts. JUST DO IT, BABY!
Here we have the other ribbon of the Velcro material…the softer material that will attach with a strong grip to the stuff I already stuck to my boards.
At this point, I have my original pieces stuck to the bottom and tops of my boards that will make up the backside of the box. I’ve cut a longer portion of the second Velcro material to attach the pieces together.
Now my three pieces of boards are attached to each other and form the bulk of the box. Standing!
Aerial view. Also note I constructed this box on the floor. I likes to get all in it and building it on the floor allows me that fun.
Here you also see the bottom board which looks attached, but in reality I just slid it into place. While I thought about cutting the side pieces to match the width of the bottom piece, it turned out just fine the way it was. Feel free to modify yours to get a more boxy look.
I decided to only attach the two side pieces and one back piece, while keeping the top and bottom loose, allowing me freedom to conform the box as I see fit. At this point, I’m ready to cut some holes in the sides and top to let the light in.
So many DIY lightboxes use tissue paper to diffuse the incoming light, but I knew that wouldn’t work for me because I’m kinda like a well-intentioned gorilla around fragile stuff. “Did I do that?!”
I knew I wanted something sturdier that could stand the test of Patti! So, I used a pearlized white vellum paper.
It’s very popular to use vellum on wedding invites. It’s a bendy, stiff, almost see-through paper. While vellum comes in all kinds of patterns, you want the pearlized with no pattern. Diffusing light is what you’re after. No patterns or colors, unless that’s what you’re after.
Because the only vellum I could find was the size of a standard piece of paper, I knew if I measured my hole the same size, the paper would be too small. Husband suggested I take a regular piece of paper, cut down the sizes a bit, then use that to trace for my holes. That way, when I places the vellum over the open spaces, it would cover completely without falling through.
Measuring…(note the antique ruler!)
Cutting success! As you can see, the vellum (back piece) is bigger than the one I’ll trace with.
After tracing, I went to work with my utility knife. Note the raggedness. This hole does not need to be perfect, but I’ll understand your OCD if you work to get it so. As for me: GOOD ENOUGH!
NOTE: While I would prefer bigger holes, until I find vellum in a bigger size than a standard sheet of paper, I had to go with what I could find. If I rigged two pieces together, the seam would cast a shadow, so that was a no-go.
I taped the vellum to the outside of the sides and top, reconstructed my box, and BAM! ready for business. Also, remember how I didn’t cut the sides to match the width of the bottom piece? Well, I found if I slid in one more foam board for the bottom (I had two more…just in case) it gave me a larger field to work within. The arrows are pointing to where the pieces of foam board abut. In the future, I may cut down the pieces and center my side openings, but until then…this collapsible lightbox works just as I had hoped.
Your light sources can be small desk lamps that flex to fit your opening’s height. While I’m using a light source from above, Boy has informed me that he has used a light box with success without a lamp above. YOUR CALL!
When I was done constructing the box, I simply unstuck the Velcro from the two side pieces and stacked all the boards and stored them in a corner standing up. (I’m keeping it real and didn’t clean up the area to make it picture perfect…this is how and where it’s stored!)
Here’s the first pic I took using the box:
While I prefer natural lighting, some days or nights, it’s just not possible. A lightbox allows more flexibility when it comes to taking pics of ALL THE THINGS (well, all the food things) for this site…FOR YOU! I mean, why should I hog the drool?
When I saw the first test shots using the box, I was relieved and giddy all in one. Relieved that I didn’t ruin the box with my bull-in-a-china-shop ways and giddy because, well, there was Cheesecake Pie in my lightbox!
See how easy it is to make a simple lightbox? If I can do it, you can do it.
Get to constructin’, my babies!